- GT2.0 48V Small Display Default Settings: P01= 002; P02= 001; P03= 048; P04= 010; P05= 005; P06= 23 or 22.8; P07= 001; P08= 100; P09= 000; P10 =002; P11= 003; P12= 005; P13= 012; P14= 012; P15= 40.0; P16/P17=0; P18=100; P19/P20=000.
- E8/E8S 48V Samll Display Default Settings: P01= 002; P02= 001; P03= 048;P04= 010; P05= 005; P06= 29.0; P07= 001; P08= 100; P09= 000; P10 =002; P11= 003; P12= 005; P13= 012; P14= 012; P15= 40.0; P16/P17=0; P18=100; P19/P20=000.
- E9 48V M5 Display Default Settings: P01= 002; P02= 001; P03= 048;P04= 010; P05= 005; P06= 29.0; P07= 001; P08= 100; P09= 000; P10 =002; P11= 003; P12= 005; P13= 012; P14= 012; P15= 40.0; P16/P17=0; P18=100; P19/P20=000.
- EB7/EB7Pro/E9Plus/EB9 M5 display default settings: P01= 002; P02= 001; P03= 048;P04= 010; P05= 005; P06= 28.0; P07= 001; P08= 100; P09= 000; P10 =002; P11= 003; P12= 005; P13= 012; P14= 012; P15= 40.0; P16/P17=0; P18=100; P19/P20=000.
To change the display settings, press the up and down arrow buttons at the same time for 5 second so enter the advanced setings. Press the "M" button will toggle between each setting numbers P01 to P20 to adjust the value of each setting, press the up or down button accordingly.
Notice: Please do not arbitrarily set other parameters unless you have understood the meaning of each parameter.
| Setting | Default | Function | Explanation |
| P01 | 002 | Screen Backlight | 3 Levels of the screen's brightness |
| P02 | 001 | Distance Units | 0:KM;1:MILE |
| P03 |
048 or 052 |
Ebike Motor Voltage; 48V ebike=48; 52V ebike= 52 |
Motor Voltage. Do not change it. Change may cause to the motor damaged； |
| P04 | 010 | Sleep Time | LCD display auto sleep time, no operation within the settingtime, the display will auto sleep and quit out the setting mode. Sleep time range is 1 to 60 minutes, 0 means no sleep. |
| P05 | 005 | PAS Gear | The pedal assist level ranges 0 to 5 |
| P06 |
28.0 or 29.0 Folding Bike:23 |
Tire Size; Please set the value according to your ebilke style. Note: E8/E9: 29.0;EB7/EB7Pro/G7/EB9: 28.0;GT2.0=22.8 or 23 |
Tire size. Used by the electronics to compute speed and distance traveled. Do not change it. Any changes may cause inaccurate speed display. |
| P07 | 001 | Speed Test Magnetic Steel | Non-professionals do not change. Change this value will display the incorrect speed on LCD. |
| P08 | 100 | Speed Limit | Speed Limit range is 0 to 50km, The input date here represents themaximum operating speed of the vehicle: for example, input 25indicates that the maximum operating speed of the vehicle will notexceed 25km/h; The drive speed is maintained at this set value.Thhe max value allowed is 55. Anything above this will not berecognize.Eror-+3KM/h. |
| P09 | 000 | Throttle Zero Start | 0: Throttle active when power is on. 1: Throttle only active after a few pedalling. |
| P10 | 002 | Mode Toggle | 0: PAS active, Throttle inactive; 1 : throttle active only when already moving; 2: Both PAS and throttle active |
| P11 | 003 | PAS Start Strength | Strength of PAS; Set strength goes up from 1 to 5. |
| P12 | 005 | PAS Sensitivity | Sensitivity of PAS sensor. Set higher numbers.will take more crank rotations for the motor to turn on. On lower numbers, it will take little crank rotation to turn on the motor |
| P13 | 012 | PAS Magnetic Type | Non-professionals do not change. |
| P14 | 12 | Controller Current Limit |
Non-professionals do not change. |
| P15 | 40.0 | Controller Undervoltage Value | Non-professionals do not change. |
| P16 | 00000 | ODO Resetting | Press the up arrow button for 5 seconds toreset the total trip mileage |
| P17 | 000 | Cruiser Setting | Function development, do not change |
| P18 | 100 |
Display Speed Scale Adjustment |
Function development, do not change |
| P19 | 000 | 0 Gear Enable Bit | Function development, do not change |
| P20 | 000 | Protocol | Function development, do not change |